Needed Tools: 2.5mm Hex Wrench, 3mm Hex Wrench
1. Remove EggRider Display Screw with 2.5mm Hex Wrench.
2. Remove pin from EggRider Display using a small nail or paper clip.
3. String cable through case and install screw that came with your EggRider Display using 2.5mm Hex Wrench.
4. Mount case onto handle bar with a 3mm Hex Wrench using provided clamp and screws.
V2 Egg Rider Foam Cable Guard
This foam will help protect the fragile Egg Rider cable from scratching and pressure. We recommend the use of this foam.
1. Peel white paper off of the included foam.
2. Apply foam to the center of the front side of the Egg rider case first.
3. Last fold under Egg Rider case to the back
]]>
The below instructions will ensure that the NTC Designs Push button start is installed successfully. If you have any further questions regarding installation, please contact us for support.
Push Button Ignition Plate Install Instructions
1. Remove existing ignition plate and disconnect USB charger and key switch.
2. Locate new ignition plate wiring harness. Cut off yellow wire down to connector.
3. Trim off stripped ends of remaining 4 wires with wire cutters as pictured below
4. Using included wire taps, insert the blue wire from the ignition plate wiring harness in the wire tap until it bottoms out. One side of the connector will bottom out, the other goes all the way through.
5. Locate the gray connector on the Sur-Ron harness that connected to the key switch. insert open side of the connector around the wire with red and white stripe.
6. Using a pair of pliers, push metal connector down until flush, then close lid.
7. Repeat steps 4-6 connecting GREEN wire from ignition plate harness to RED/BLACK wire going to stock key switch connector.
8. Repeat steps 4-6 connecting RED wire from ignition plate harness to GREEN wire that connects to USB charger.
9. Repeat steps 4-6 connection BLACK wire from ignition plate harness to BLACK wire that connects USB charger.
Wiring Guide | ||
---|---|---|
Ignition Plate Wire | Sur-Ron Wire | Function |
Blue | Red/White | Switch N/O |
Green | Red/Black | Switch N/O |
Red | Green | LED + |
Black | Black | LED - |
Your stock Sur Ron is fun to ride once you get up to speed, but you quickly develop a hunger for more power and pull right off the line and around each corner. The BAC Controller upgrades the Sur Ron from a power lacking dog to a dirt-eating, off-road cheetah. The NTC Designs Full Coverage Mount Kit is the best way to keep your new controller safe for off road adventures!
The increase in power from a 60V system to a 72V system is very noticeable. This is also the ideal time to grab a larger battery to increase your range as well.
The below instructions will ensure that the NTC Designs Mount Kit is installed successfully. Refer to the BAC Controller Upgrade instructions for proper wiring of controller.
Install Instructions for the BAC 4000 Full Coverage Controller Mount Kit:
Remove stock controller and connect your BAC Controller per the instructions provided from whom you purchased it.
Remove Stock tilt sensor, sensor bracket and lower left and right mount brackets.
The following Install Instructions Apply to BAC 4000 Full Coverage Controller Upgrade:
Set Controller, NTC Mount Plate, NTC Brackets, BAC Wiring Harness and provided Hardware in front of you.
Bolt on Upper and Lower NTC Designs Mount Brackets.
Insert first NTC Spacer, secondly the BAC controller and lastly the second NTC Spacer into grooves of NTC Mount Plate and secure with set screws provided.
Carefully route wires and get the upper or lower 2 mount screws started with hex key. If your wires are very large, this step might require some patience and creative wire routing. In my case, the wires are very large in diameter as pictured, so it was advantageous to get the top 2 bolts started to allow me to route the wires near the bottom and tuck the bottom in.
Lastly, fasten the NTC Designs Mount plate tightly with all four bolts provided to the upper and lower mounting arms.
Congratulations! You have reached the end of the install instructions! Hopefully there is still some daylight left to go test out your upgraded bike out on the trail! Have a great day!
]]>
Now that there are 2 Egg Rider display versions available, We wanted to make a post showing the difference between the two. This makes choosing the right case for your display a breeze.
Below is a picture of the back of the Egg Rider Version 1 which is compatible with the NTC Egg Rider V1 Display Case. This version has the clamp mount off to one side as seen below.
The next picture below shows the Egg Rider Version 2 which is compatible with the NTC Egg Rider V2 Display Case. This version has the clamp mount centered as seen below.
At NTC Designs, we are honored and excited to get these 2 products on your bike and on the trails in the coming months. Hopefully this has provided the clarity you need to choose the appropriate Display Case for your Egg Rider Display.
Cheers to another great day behind bars!
]]>The Design Team at NTC has developed yet another product to enhance the quality and longevity of your Sur Ron rides! No longer must you fear throttling around a blind corner or ripping up an unknown hill because our latest addition to the product lineup can handle the roughest of terrain.
The NTC Designs Nucular Display Case brings the rigidity and added visual appeal that you desire. It is machined from 6061 billet aluminum and mounted using a creative riser design that utilizes interior pocket holes for mounting to ensure a clean and custom appearance after installation.
This rugged custom case protects the plastic stock case from damage both on the trail or in the garage. It also replaces the plastic bar clamp with dual all-aluminum 2 screw clamps (similar to brake lever clamp). Mounting one riser and one clamp is a technique that can be used as needed. ..
The risers come in 2 sizes, standard and low profile, which will accommodate most configurations. Direct mount stems will likely accept the low profile risers. Stock stems most likely will accept the standard riser.
Looking to purchase this one of a kind case? Check it out here. If you have already purchased and are looking for some quick and easy but in depth install instructions see those below.